| 1 | /*
|
|---|
| 2 | * Copyright (c) 1993 Herb Peyerl ([email protected]) All rights reserved.
|
|---|
| 3 | *
|
|---|
| 4 | * Redistribution and use in source and binary forms, with or without
|
|---|
| 5 | * modification, are permitted provided that the following conditions are
|
|---|
| 6 | * met: 1. Redistributions of source code must retain the above copyright
|
|---|
| 7 | * notice, this list of conditions and the following disclaimer. 2. The name
|
|---|
| 8 | * of the author may not be used to endorse or promote products derived from
|
|---|
| 9 | * this software without specific prior written permission
|
|---|
| 10 | *
|
|---|
| 11 | * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED
|
|---|
| 12 | * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|---|
| 13 | * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
|
|---|
| 14 | * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
|---|
| 15 | * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
|
|---|
| 16 | * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
|
|---|
| 17 | * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
|
|---|
| 18 | * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
|
|---|
| 19 | * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|---|
| 20 | * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|---|
| 21 | *
|
|---|
| 22 | October 2, 1994
|
|---|
| 23 |
|
|---|
| 24 | Modified by: Andres Vega Garcia
|
|---|
| 25 |
|
|---|
| 26 | INRIA - Sophia Antipolis, France
|
|---|
| 27 | e-mail: [email protected]
|
|---|
| 28 | finger: [email protected]
|
|---|
| 29 |
|
|---|
| 30 | */
|
|---|
| 31 |
|
|---|
| 32 | FILE_LICENCE ( BSD3 );
|
|---|
| 33 |
|
|---|
| 34 | /*
|
|---|
| 35 | * Created from if_epreg.h by Fred Gray ([email protected]) to support the
|
|---|
| 36 | * 3c590 family.
|
|---|
| 37 | */
|
|---|
| 38 |
|
|---|
| 39 | /*
|
|---|
| 40 | * Modified by Shusuke Nisiyama <[email protected]>
|
|---|
| 41 | * for etherboot
|
|---|
| 42 | * Mar. 14, 2000
|
|---|
| 43 | */
|
|---|
| 44 |
|
|---|
| 45 | /*
|
|---|
| 46 | * Ethernet software status per interface.
|
|---|
| 47 | */
|
|---|
| 48 |
|
|---|
| 49 | /*
|
|---|
| 50 | * Some global constants
|
|---|
| 51 | */
|
|---|
| 52 |
|
|---|
| 53 | #define TX_INIT_RATE 16
|
|---|
| 54 | #define TX_INIT_MAX_RATE 64
|
|---|
| 55 | #define RX_INIT_LATENCY 64
|
|---|
| 56 | #define RX_INIT_EARLY_THRESH 64
|
|---|
| 57 | #define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */
|
|---|
| 58 | #define MIN_RX_EARLY_THRESHL 4
|
|---|
| 59 |
|
|---|
| 60 | #define EEPROMSIZE 0x40
|
|---|
| 61 | #define MAX_EEPROMBUSY 1000
|
|---|
| 62 | #define VX_LAST_TAG 0xd7
|
|---|
| 63 | #define VX_MAX_BOARDS 16
|
|---|
| 64 | #define VX_ID_PORT 0x100
|
|---|
| 65 |
|
|---|
| 66 | /*
|
|---|
| 67 | * some macros to acces long named fields
|
|---|
| 68 | */
|
|---|
| 69 | #define BASE (eth_nic_base)
|
|---|
| 70 |
|
|---|
| 71 | /*
|
|---|
| 72 | * Commands to read/write EEPROM trough EEPROM command register (Window 0,
|
|---|
| 73 | * Offset 0xa)
|
|---|
| 74 | */
|
|---|
| 75 | #define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */
|
|---|
| 76 | #define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */
|
|---|
| 77 | #define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */
|
|---|
| 78 | #define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */
|
|---|
| 79 |
|
|---|
| 80 | #define EEPROM_BUSY (1<<15)
|
|---|
| 81 |
|
|---|
| 82 | /*
|
|---|
| 83 | * Some short functions, worth to let them be a macro
|
|---|
| 84 | */
|
|---|
| 85 |
|
|---|
| 86 | /**************************************************************************
|
|---|
| 87 | * *
|
|---|
| 88 | * These define the EEPROM data structure. They are used in the probe
|
|---|
| 89 | * function to verify the existence of the adapter after having sent
|
|---|
| 90 | * the ID_Sequence.
|
|---|
| 91 | *
|
|---|
| 92 | * There are others but only the ones we use are defined here.
|
|---|
| 93 | *
|
|---|
| 94 | **************************************************************************/
|
|---|
| 95 |
|
|---|
| 96 | #define EEPROM_NODE_ADDR_0 0x0 /* Word */
|
|---|
| 97 | #define EEPROM_NODE_ADDR_1 0x1 /* Word */
|
|---|
| 98 | #define EEPROM_NODE_ADDR_2 0x2 /* Word */
|
|---|
| 99 | #define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */
|
|---|
| 100 | #define EEPROM_MFG_ID 0x7 /* 0x6d50 */
|
|---|
| 101 | #define EEPROM_ADDR_CFG 0x8 /* Base addr */
|
|---|
| 102 | #define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */
|
|---|
| 103 | #define EEPROM_OEM_ADDR_0 0xa /* Word */
|
|---|
| 104 | #define EEPROM_OEM_ADDR_1 0xb /* Word */
|
|---|
| 105 | #define EEPROM_OEM_ADDR_2 0xc /* Word */
|
|---|
| 106 | #define EEPROM_SOFT_INFO_2 0xf /* Software information 2 */
|
|---|
| 107 |
|
|---|
| 108 | #define NO_RX_OVN_ANOMALY (1<<5)
|
|---|
| 109 |
|
|---|
| 110 | /**************************************************************************
|
|---|
| 111 | * *
|
|---|
| 112 | * These are the registers for the 3Com 3c509 and their bit patterns when *
|
|---|
| 113 | * applicable. They have been taken out the "EtherLink III Parallel *
|
|---|
| 114 | * Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual *
|
|---|
| 115 | * from 3com. *
|
|---|
| 116 | * *
|
|---|
| 117 | **************************************************************************/
|
|---|
| 118 |
|
|---|
| 119 | #define VX_COMMAND 0x0e /* Write. BASE+0x0e is always a
|
|---|
| 120 | * command reg. */
|
|---|
| 121 | #define VX_STATUS 0x0e /* Read. BASE+0x0e is always status
|
|---|
| 122 | * reg. */
|
|---|
| 123 | #define VX_WINDOW 0x0f /* Read. BASE+0x0f is always window
|
|---|
| 124 | * reg. */
|
|---|
| 125 | /*
|
|---|
| 126 | * Window 0 registers. Setup.
|
|---|
| 127 | */
|
|---|
| 128 | /* Write */
|
|---|
| 129 | #define VX_W0_EEPROM_DATA 0x0c
|
|---|
| 130 | #define VX_W0_EEPROM_COMMAND 0x0a
|
|---|
| 131 | #define VX_W0_RESOURCE_CFG 0x08
|
|---|
| 132 | #define VX_W0_ADDRESS_CFG 0x06
|
|---|
| 133 | #define VX_W0_CONFIG_CTRL 0x04
|
|---|
| 134 | /* Read */
|
|---|
| 135 | #define VX_W0_PRODUCT_ID 0x02
|
|---|
| 136 | #define VX_W0_MFG_ID 0x00
|
|---|
| 137 |
|
|---|
| 138 |
|
|---|
| 139 | /*
|
|---|
| 140 | * Window 1 registers. Operating Set.
|
|---|
| 141 | */
|
|---|
| 142 | /* Write */
|
|---|
| 143 | #define VX_W1_TX_PIO_WR_2 0x02
|
|---|
| 144 | #define VX_W1_TX_PIO_WR_1 0x00
|
|---|
| 145 | /* Read */
|
|---|
| 146 | #define VX_W1_FREE_TX 0x0c
|
|---|
| 147 | #define VX_W1_TX_STATUS 0x0b /* byte */
|
|---|
| 148 | #define VX_W1_TIMER 0x0a /* byte */
|
|---|
| 149 | #define VX_W1_RX_STATUS 0x08
|
|---|
| 150 | #define VX_W1_RX_PIO_RD_2 0x02
|
|---|
| 151 | #define VX_W1_RX_PIO_RD_1 0x00
|
|---|
| 152 |
|
|---|
| 153 | /*
|
|---|
| 154 | * Window 2 registers. Station Address Setup/Read
|
|---|
| 155 | */
|
|---|
| 156 | /* Read/Write */
|
|---|
| 157 | #define VX_W2_ADDR_5 0x05
|
|---|
| 158 | #define VX_W2_ADDR_4 0x04
|
|---|
| 159 | #define VX_W2_ADDR_3 0x03
|
|---|
| 160 | #define VX_W2_ADDR_2 0x02
|
|---|
| 161 | #define VX_W2_ADDR_1 0x01
|
|---|
| 162 | #define VX_W2_ADDR_0 0x00
|
|---|
| 163 |
|
|---|
| 164 | /*
|
|---|
| 165 | * Window 3 registers. FIFO Management.
|
|---|
| 166 | */
|
|---|
| 167 | /* Read */
|
|---|
| 168 | #define VX_W3_INTERNAL_CFG 0x00
|
|---|
| 169 | #define VX_W3_RESET_OPT 0x08
|
|---|
| 170 | #define VX_W3_FREE_TX 0x0c
|
|---|
| 171 | #define VX_W3_FREE_RX 0x0a
|
|---|
| 172 |
|
|---|
| 173 | /*
|
|---|
| 174 | * Window 4 registers. Diagnostics.
|
|---|
| 175 | */
|
|---|
| 176 | /* Read/Write */
|
|---|
| 177 | #define VX_W4_MEDIA_TYPE 0x0a
|
|---|
| 178 | #define VX_W4_CTRLR_STATUS 0x08
|
|---|
| 179 | #define VX_W4_NET_DIAG 0x06
|
|---|
| 180 | #define VX_W4_FIFO_DIAG 0x04
|
|---|
| 181 | #define VX_W4_HOST_DIAG 0x02
|
|---|
| 182 | #define VX_W4_TX_DIAG 0x00
|
|---|
| 183 |
|
|---|
| 184 | /*
|
|---|
| 185 | * Window 5 Registers. Results and Internal status.
|
|---|
| 186 | */
|
|---|
| 187 | /* Read */
|
|---|
| 188 | #define VX_W5_READ_0_MASK 0x0c
|
|---|
| 189 | #define VX_W5_INTR_MASK 0x0a
|
|---|
| 190 | #define VX_W5_RX_FILTER 0x08
|
|---|
| 191 | #define VX_W5_RX_EARLY_THRESH 0x06
|
|---|
| 192 | #define VX_W5_TX_AVAIL_THRESH 0x02
|
|---|
| 193 | #define VX_W5_TX_START_THRESH 0x00
|
|---|
| 194 |
|
|---|
| 195 | /*
|
|---|
| 196 | * Window 6 registers. Statistics.
|
|---|
| 197 | */
|
|---|
| 198 | /* Read/Write */
|
|---|
| 199 | #define TX_TOTAL_OK 0x0c
|
|---|
| 200 | #define RX_TOTAL_OK 0x0a
|
|---|
| 201 | #define TX_DEFERRALS 0x08
|
|---|
| 202 | #define RX_FRAMES_OK 0x07
|
|---|
| 203 | #define TX_FRAMES_OK 0x06
|
|---|
| 204 | #define RX_OVERRUNS 0x05
|
|---|
| 205 | #define TX_COLLISIONS 0x04
|
|---|
| 206 | #define TX_AFTER_1_COLLISION 0x03
|
|---|
| 207 | #define TX_AFTER_X_COLLISIONS 0x02
|
|---|
| 208 | #define TX_NO_SQE 0x01
|
|---|
| 209 | #define TX_CD_LOST 0x00
|
|---|
| 210 |
|
|---|
| 211 | /****************************************
|
|---|
| 212 | *
|
|---|
| 213 | * Register definitions.
|
|---|
| 214 | *
|
|---|
| 215 | ****************************************/
|
|---|
| 216 |
|
|---|
| 217 | /*
|
|---|
| 218 | * Command register. All windows.
|
|---|
| 219 | *
|
|---|
| 220 | * 16 bit register.
|
|---|
| 221 | * 15-11: 5-bit code for command to be executed.
|
|---|
| 222 | * 10-0: 11-bit arg if any. For commands with no args;
|
|---|
| 223 | * this can be set to anything.
|
|---|
| 224 | */
|
|---|
| 225 | #define GLOBAL_RESET (unsigned short) 0x0000 /* Wait at least 1ms
|
|---|
| 226 | * after issuing */
|
|---|
| 227 | #define WINDOW_SELECT (unsigned short) (0x1<<11)
|
|---|
| 228 | #define START_TRANSCEIVER (unsigned short) (0x2<<11) /* Read ADDR_CFG reg to
|
|---|
| 229 | * determine whether
|
|---|
| 230 | * this is needed. If
|
|---|
| 231 | * so; wait 800 uSec
|
|---|
| 232 | * before using trans-
|
|---|
| 233 | * ceiver. */
|
|---|
| 234 | #define RX_DISABLE (unsigned short) (0x3<<11) /* state disabled on
|
|---|
| 235 | * power-up */
|
|---|
| 236 | #define RX_ENABLE (unsigned short) (0x4<<11)
|
|---|
| 237 | #define RX_RESET (unsigned short) (0x5<<11)
|
|---|
| 238 | #define RX_DISCARD_TOP_PACK (unsigned short) (0x8<<11)
|
|---|
| 239 | #define TX_ENABLE (unsigned short) (0x9<<11)
|
|---|
| 240 | #define TX_DISABLE (unsigned short) (0xa<<11)
|
|---|
| 241 | #define TX_RESET (unsigned short) (0xb<<11)
|
|---|
| 242 | #define REQ_INTR (unsigned short) (0xc<<11)
|
|---|
| 243 | /*
|
|---|
| 244 | * The following C_* acknowledge the various interrupts. Some of them don't
|
|---|
| 245 | * do anything. See the manual.
|
|---|
| 246 | */
|
|---|
| 247 | #define ACK_INTR (unsigned short) (0x6800)
|
|---|
| 248 | # define C_INTR_LATCH (unsigned short) (ACK_INTR|0x1)
|
|---|
| 249 | # define C_CARD_FAILURE (unsigned short) (ACK_INTR|0x2)
|
|---|
| 250 | # define C_TX_COMPLETE (unsigned short) (ACK_INTR|0x4)
|
|---|
| 251 | # define C_TX_AVAIL (unsigned short) (ACK_INTR|0x8)
|
|---|
| 252 | # define C_RX_COMPLETE (unsigned short) (ACK_INTR|0x10)
|
|---|
| 253 | # define C_RX_EARLY (unsigned short) (ACK_INTR|0x20)
|
|---|
| 254 | # define C_INT_RQD (unsigned short) (ACK_INTR|0x40)
|
|---|
| 255 | # define C_UPD_STATS (unsigned short) (ACK_INTR|0x80)
|
|---|
| 256 | #define SET_INTR_MASK (unsigned short) (0xe<<11)
|
|---|
| 257 | #define SET_RD_0_MASK (unsigned short) (0xf<<11)
|
|---|
| 258 | #define SET_RX_FILTER (unsigned short) (0x10<<11)
|
|---|
| 259 | # define FIL_INDIVIDUAL (unsigned short) (0x1)
|
|---|
| 260 | # define FIL_MULTICAST (unsigned short) (0x02)
|
|---|
| 261 | # define FIL_BRDCST (unsigned short) (0x04)
|
|---|
| 262 | # define FIL_PROMISC (unsigned short) (0x08)
|
|---|
| 263 | #define SET_RX_EARLY_THRESH (unsigned short) (0x11<<11)
|
|---|
| 264 | #define SET_TX_AVAIL_THRESH (unsigned short) (0x12<<11)
|
|---|
| 265 | #define SET_TX_START_THRESH (unsigned short) (0x13<<11)
|
|---|
| 266 | #define STATS_ENABLE (unsigned short) (0x15<<11)
|
|---|
| 267 | #define STATS_DISABLE (unsigned short) (0x16<<11)
|
|---|
| 268 | #define STOP_TRANSCEIVER (unsigned short) (0x17<<11)
|
|---|
| 269 |
|
|---|
| 270 | /*
|
|---|
| 271 | * Status register. All windows.
|
|---|
| 272 | *
|
|---|
| 273 | * 15-13: Window number(0-7).
|
|---|
| 274 | * 12: Command_in_progress.
|
|---|
| 275 | * 11: reserved.
|
|---|
| 276 | * 10: reserved.
|
|---|
| 277 | * 9: reserved.
|
|---|
| 278 | * 8: reserved.
|
|---|
| 279 | * 7: Update Statistics.
|
|---|
| 280 | * 6: Interrupt Requested.
|
|---|
| 281 | * 5: RX Early.
|
|---|
| 282 | * 4: RX Complete.
|
|---|
| 283 | * 3: TX Available.
|
|---|
| 284 | * 2: TX Complete.
|
|---|
| 285 | * 1: Adapter Failure.
|
|---|
| 286 | * 0: Interrupt Latch.
|
|---|
| 287 | */
|
|---|
| 288 | #define S_INTR_LATCH (unsigned short) (0x1)
|
|---|
| 289 | #define S_CARD_FAILURE (unsigned short) (0x2)
|
|---|
| 290 | #define S_TX_COMPLETE (unsigned short) (0x4)
|
|---|
| 291 | #define S_TX_AVAIL (unsigned short) (0x8)
|
|---|
| 292 | #define S_RX_COMPLETE (unsigned short) (0x10)
|
|---|
| 293 | #define S_RX_EARLY (unsigned short) (0x20)
|
|---|
| 294 | #define S_INT_RQD (unsigned short) (0x40)
|
|---|
| 295 | #define S_UPD_STATS (unsigned short) (0x80)
|
|---|
| 296 | #define S_COMMAND_IN_PROGRESS (unsigned short) (0x1000)
|
|---|
| 297 |
|
|---|
| 298 | #define VX_BUSY_WAIT while (inw(BASE + VX_STATUS) & S_COMMAND_IN_PROGRESS)
|
|---|
| 299 |
|
|---|
| 300 | /* Address Config. Register.
|
|---|
| 301 | * Window 0/Port 06
|
|---|
| 302 | */
|
|---|
| 303 |
|
|---|
| 304 | #define ACF_CONNECTOR_BITS 14
|
|---|
| 305 | #define ACF_CONNECTOR_UTP 0
|
|---|
| 306 | #define ACF_CONNECTOR_AUI 1
|
|---|
| 307 | #define ACF_CONNECTOR_BNC 3
|
|---|
| 308 |
|
|---|
| 309 | #define INTERNAL_CONNECTOR_BITS 20
|
|---|
| 310 | #define INTERNAL_CONNECTOR_MASK 0x01700000
|
|---|
| 311 |
|
|---|
| 312 | /*
|
|---|
| 313 | * FIFO Registers. RX Status.
|
|---|
| 314 | *
|
|---|
| 315 | * 15: Incomplete or FIFO empty.
|
|---|
| 316 | * 14: 1: Error in RX Packet 0: Incomplete or no error.
|
|---|
| 317 | * 13-11: Type of error.
|
|---|
| 318 | * 1000 = Overrun.
|
|---|
| 319 | * 1011 = Run Packet Error.
|
|---|
| 320 | * 1100 = Alignment Error.
|
|---|
| 321 | * 1101 = CRC Error.
|
|---|
| 322 | * 1001 = Oversize Packet Error (>1514 bytes)
|
|---|
| 323 | * 0010 = Dribble Bits.
|
|---|
| 324 | * (all other error codes, no errors.)
|
|---|
| 325 | *
|
|---|
| 326 | * 10-0: RX Bytes (0-1514)
|
|---|
| 327 | */
|
|---|
| 328 | #define ERR_INCOMPLETE (unsigned short) (0x8000)
|
|---|
| 329 | #define ERR_RX (unsigned short) (0x4000)
|
|---|
| 330 | #define ERR_MASK (unsigned short) (0x7800)
|
|---|
| 331 | #define ERR_OVERRUN (unsigned short) (0x4000)
|
|---|
| 332 | #define ERR_RUNT (unsigned short) (0x5800)
|
|---|
| 333 | #define ERR_ALIGNMENT (unsigned short) (0x6000)
|
|---|
| 334 | #define ERR_CRC (unsigned short) (0x6800)
|
|---|
| 335 | #define ERR_OVERSIZE (unsigned short) (0x4800)
|
|---|
| 336 | #define ERR_DRIBBLE (unsigned short) (0x1000)
|
|---|
| 337 |
|
|---|
| 338 | /*
|
|---|
| 339 | * TX Status.
|
|---|
| 340 | *
|
|---|
| 341 | * Reports the transmit status of a completed transmission. Writing this
|
|---|
| 342 | * register pops the transmit completion stack.
|
|---|
| 343 | *
|
|---|
| 344 | * Window 1/Port 0x0b.
|
|---|
| 345 | *
|
|---|
| 346 | * 7: Complete
|
|---|
| 347 | * 6: Interrupt on successful transmission requested.
|
|---|
| 348 | * 5: Jabber Error (TP Only, TX Reset required. )
|
|---|
| 349 | * 4: Underrun (TX Reset required. )
|
|---|
| 350 | * 3: Maximum Collisions.
|
|---|
| 351 | * 2: TX Status Overflow.
|
|---|
| 352 | * 1-0: Undefined.
|
|---|
| 353 | *
|
|---|
| 354 | */
|
|---|
| 355 | #define TXS_COMPLETE 0x80
|
|---|
| 356 | #define TXS_INTR_REQ 0x40
|
|---|
| 357 | #define TXS_JABBER 0x20
|
|---|
| 358 | #define TXS_UNDERRUN 0x10
|
|---|
| 359 | #define TXS_MAX_COLLISION 0x8
|
|---|
| 360 | #define TXS_STATUS_OVERFLOW 0x4
|
|---|
| 361 |
|
|---|
| 362 | #define RS_AUI (1<<5)
|
|---|
| 363 | #define RS_BNC (1<<4)
|
|---|
| 364 | #define RS_UTP (1<<3)
|
|---|
| 365 | #define RS_T4 (1<<0)
|
|---|
| 366 | #define RS_TX (1<<1)
|
|---|
| 367 | #define RS_FX (1<<2)
|
|---|
| 368 | #define RS_MII (1<<6)
|
|---|
| 369 |
|
|---|
| 370 |
|
|---|
| 371 | /*
|
|---|
| 372 | * FIFO Status (Window 4)
|
|---|
| 373 | *
|
|---|
| 374 | * Supports FIFO diagnostics
|
|---|
| 375 | *
|
|---|
| 376 | * Window 4/Port 0x04.1
|
|---|
| 377 | *
|
|---|
| 378 | * 15: 1=RX receiving (RO). Set when a packet is being received
|
|---|
| 379 | * into the RX FIFO.
|
|---|
| 380 | * 14: Reserved
|
|---|
| 381 | * 13: 1=RX underrun (RO). Generates Adapter Failure interrupt.
|
|---|
| 382 | * Requires RX Reset or Global Reset command to recover.
|
|---|
| 383 | * It is generated when you read past the end of a packet -
|
|---|
| 384 | * reading past what has been received so far will give bad
|
|---|
| 385 | * data.
|
|---|
| 386 | * 12: 1=RX status overrun (RO). Set when there are already 8
|
|---|
| 387 | * packets in the RX FIFO. While this bit is set, no additional
|
|---|
| 388 | * packets are received. Requires no action on the part of
|
|---|
| 389 | * the host. The condition is cleared once a packet has been
|
|---|
| 390 | * read out of the RX FIFO.
|
|---|
| 391 | * 11: 1=RX overrun (RO). Set when the RX FIFO is full (there
|
|---|
| 392 | * may not be an overrun packet yet). While this bit is set,
|
|---|
| 393 | * no additional packets will be received (some additional
|
|---|
| 394 | * bytes can still be pending between the wire and the RX
|
|---|
| 395 | * FIFO). Requires no action on the part of the host. The
|
|---|
| 396 | * condition is cleared once a few bytes have been read out
|
|---|
| 397 | * from the RX FIFO.
|
|---|
| 398 | * 10: 1=TX overrun (RO). Generates adapter failure interrupt.
|
|---|
| 399 | * Requires TX Reset or Global Reset command to recover.
|
|---|
| 400 | * Disables Transmitter.
|
|---|
| 401 | * 9-8: Unassigned.
|
|---|
| 402 | * 7-0: Built in self test bits for the RX and TX FIFO's.
|
|---|
| 403 | */
|
|---|
| 404 | #define FIFOS_RX_RECEIVING (unsigned short) 0x8000
|
|---|
| 405 | #define FIFOS_RX_UNDERRUN (unsigned short) 0x2000
|
|---|
| 406 | #define FIFOS_RX_STATUS_OVERRUN (unsigned short) 0x1000
|
|---|
| 407 | #define FIFOS_RX_OVERRUN (unsigned short) 0x0800
|
|---|
| 408 | #define FIFOS_TX_OVERRUN (unsigned short) 0x0400
|
|---|
| 409 |
|
|---|
| 410 | /*
|
|---|
| 411 | * Misc defines for various things.
|
|---|
| 412 | */
|
|---|
| 413 | #define TAG_ADAPTER 0xd0
|
|---|
| 414 | #define ACTIVATE_ADAPTER_TO_CONFIG 0xff
|
|---|
| 415 | #define ENABLE_DRQ_IRQ 0x0001
|
|---|
| 416 | #define MFG_ID 0x506d /* `TCM' */
|
|---|
| 417 | #define PROD_ID 0x5090
|
|---|
| 418 | #define GO_WINDOW(x) outw(WINDOW_SELECT|(x),BASE+VX_COMMAND)
|
|---|
| 419 | #define JABBER_GUARD_ENABLE 0x40
|
|---|
| 420 | #define LINKBEAT_ENABLE 0x80
|
|---|
| 421 | #define ENABLE_UTP (JABBER_GUARD_ENABLE | LINKBEAT_ENABLE)
|
|---|
| 422 | #define DISABLE_UTP 0x0
|
|---|
| 423 | #define RX_BYTES_MASK (unsigned short) (0x07ff)
|
|---|
| 424 | #define RX_ERROR 0x4000
|
|---|
| 425 | #define RX_INCOMPLETE 0x8000
|
|---|
| 426 | #define TX_INDICATE 1<<15
|
|---|
| 427 | #define is_eeprom_busy(b) (inw((b)+VX_W0_EEPROM_COMMAND)&EEPROM_BUSY)
|
|---|
| 428 |
|
|---|
| 429 | #define VX_IOSIZE 0x20
|
|---|
| 430 |
|
|---|
| 431 | #define VX_CONNECTORS 8
|
|---|
| 432 |
|
|---|
| 433 | /*
|
|---|
| 434 | * Local variables:
|
|---|
| 435 | * c-basic-offset: 8
|
|---|
| 436 | * End:
|
|---|
| 437 | */
|
|---|
