; $Id: bootsector2-triple-fault-1.asm 76553 2019-01-01 01:45:53Z vboxsync $ ;; @file ; Bootsector for testing triple faults. ; ; ; Copyright (C) 2007-2019 Oracle Corporation ; ; This file is part of VirtualBox Open Source Edition (OSE), as ; available from http://www.virtualbox.org. This file is free software; ; you can redistribute it and/or modify it under the terms of the GNU ; General Public License (GPL) as published by the Free Software ; Foundation, in version 2 as it comes in the "COPYING" file of the ; VirtualBox OSE distribution. VirtualBox OSE is distributed in the ; hope that it will be useful, but WITHOUT ANY WARRANTY of any kind. ; ; The contents of this file may alternatively be used under the terms ; of the Common Development and Distribution License Version 1.0 ; (CDDL) only, as it comes in the "COPYING.CDDL" file of the ; VirtualBox OSE distribution, in which case the provisions of the ; CDDL are applicable instead of those of the GPL. ; ; You may elect to license modified versions of this file under the ; terms and conditions of either the GPL or the CDDL or both. ; %include "iprt/asmdefs.mac" %include "iprt/x86.mac" %include "VBox/VMMDevTesting.mac" ;; The number of instructions to test. %define TEST_INSTRUCTION_COUNT_IO 2000000 ;; The number of instructions to test. %define TEST_INSTRUCTION_COUNT_MMIO 750000 ;; Define this to drop unnecessary test variations. %define QUICK_TEST ; ; Include and execute the init code. ; %define BS2_INIT_RM %define BS2_INC_PE16 %define BS2_INC_PE32 %define BS2_INC_PP32 %define BS2_INC_PAE32 %define BS2_INC_LM64 %include "bootsector2-common-init-code.mac" ; ; The test driver ; BEGINPROC main ; ; Test prologue. ; mov ax, .s_szTstName call TestInit_r86 call Bs2EnableA20_r86 ; ; Did we get here from a reboot triggered below? ; push ds mov ax, 2000h ; 128 KB is enough for the test program .boot_check_loop: mov ds, ax cmp dword [0], 064726962h jne .boot_check_next cmp dword [4], 062697264h je .warm_reset_broken .boot_check_next: mov dword [0], 064726962h mov dword [4], 062697264h add ax, 1000h cmp ax, 8000h jbe .boot_check_loop pop ds jmp .fine .warm_reset_broken: pop ds mov ax, .s_szWarmResetBroken call NAME(TestFailed_r86) jmp .done .s_szWarmResetBroken: db 'Warm reset vector support is broken', 0dh, 0ah, 0 .fine: ; ; Test that the warm reset interface works. ; mov ax, .s_szPrecondTest5 call NAME(TestSub_r86) mov al, 05h call NAME(SetWarmResetJmp) cmp ax, 0 jne .precond_test_A call NAME(TestReboot_r86) .precond_test_A: mov ax, .s_szPrecondTestA call NAME(TestSub_r86) mov al, 0Ah call NAME(SetWarmResetJmp) cmp ax, 0 jne .precond_test_A_passed call NAME(TestReboot_r86) .precond_test_A_passed: call NAME(TestSubDone_r86) ; ; The real tests. ; ; ; We're done. ; .done: call NAME(TestTerm_r86) call Bs2Panic .s_szTstName: db 'tstTriple', 0 .s_szPrecondTest5: db 'Shutdown Action 5', 0 .s_szPrecondTestA: db 'Shutdown Action A', 0 ENDPROC main ;; ; Sets up the warm reset vector. ; ; @param ax Where to resume exeuction. ; @param dl Shutdown action command to use, 5h or Fh. ; ; @uses nothing ; BEGINPROC SetUpWarmReset push bp mov bp, sp push eax push ebx push ecx push edx push edi push esi push es ; ; Set up the warm reboot vector. ; mov bx, 40h mov es, bx mov ecx, [es:67h] ; debug mov word [es:67h], ax mov bx, cs mov word [es:67h+2], bx mov bx, [es:72h] ; debug mov word [es:72h], 1234h ; warm reboot wbinvd mov al, 0fh out 70h, al ; set register index in al, 71h mov ah, al ; debug mov al, dl ; shutdown action command out 71h, al ; set cmos[f] = a - invoke testResume as early as possible. in al, 71h ; debug / paranoia movzx si, al ; Debug print. %if 1 mov di, sp ; save sp (lazy bird) in al, 64h push ax ; kbd status push si ; cmos[f] after mov al, ah ; cmos[f] before push ax push word [0472h] ; 40:72 word after push bx ; 40:72 word before push word [0467h] ; 40:67 far addr after push word [0469h] push cx ; 40:67 far addr before shr ecx, 16 push dx push ds push .s_szDebugFmt call NAME(PrintF_r86) mov sp, di ; restore sp. ;.forever: ; cli ; hlt ; jmp .forever %endif pop es pop esi pop edi pop edx pop ecx pop ebx pop eax leave ret .s_szDebugFmt: db 'dbg: 40:67=%RX16:%RX16 (%RX16:%RX16) 40:72=%RX16 (%RX16) cmos[f]=%RX8 (%RX8) kbdsts=%RX8', 0dh, 0ah, 0 ENDPROC SetUpWarmReset ;; ; Sets up the warm reset vector. ; ; @returns ax = 0 on setup call, ax = 1 on resume return. ; @param al Shutdown action command to use, 5h or Fh. ; @uses ax ; BEGINPROC SetWarmResetJmp push bp mov bp, sp push dx mov dl, al mov ax, .resume call NAME(SetUpWarmReset) %ifdef DEBUG push cs push .s_szDbg1 call NAME(PrintF_r86) add sp, 4 %endif mov ax, .s_ResumeRegs call NAME(TestSaveRegisters_r86) %ifdef DEBUG push cs push .s_szDbg2 call NAME(PrintF_r86) add sp, 4 %endif mov dx, [bp - 2] mov [.s_ResumeRegs + BS2REGS.rdx], dx mov ax, bp add ax, 4 mov [.s_ResumeRegs + BS2REGS.rsp], ax mov ax, [bp] mov [.s_ResumeRegs + BS2REGS.rbp], ax mov ax, [bp + 2] mov [.s_ResumeRegs + BS2REGS.rip], ax mov word [.s_ResumeRegs + BS2REGS.rax], 1 %ifdef DEBUG push cs push .s_szDbg3 call NAME(PrintF_r86) add sp, 4 %endif xor ax, ax .done: pop dx leave ret .resume: cli xor ax, ax mov ds, ax mov es, ax mov ax, [.s_ResumeRegs + BS2REGS.ss] mov ss, ax mov esp, [.s_ResumeRegs + BS2REGS.rsp] mov ebp, [.s_ResumeRegs + BS2REGS.rbp] %ifdef DEBUG push ds push .s_szDbg4 call NAME(PrintF_r86) add sp, 4 %endif mov ax, .s_ResumeRegs call NAME(TestRestoreRegisters_r86) mov ax, [.s_ResumeRegs + BS2REGS.rip] push ax mov ax, 1 ret ;jmp word [.s_ResumeRegs + BS2REGS.rip] .s_ResumeRegs: times (BS2REGS_size) db 0 %ifdef DEBUG .s_szDbg1: db 'dbg 1', 0dh, 0ah, 0 .s_szDbg2: db 'dbg 2', 0dh, 0ah, 0 .s_szDbg3: db 'dbg 3', 0dh, 0ah, 0 .s_szDbg4: db 'dbg 4', 0dh, 0ah, 0 %endif ENDPROC SetWarmResetJmp ;; ; Reboot the machine. Will not return. ; BEGINPROC TestReboot_r86 %ifdef DEBUG ; Debug push ds push .s_szDbg call NAME(PrintF_r86) %endif ; Via port A in al, 92h and al, ~1 out 92h, al or al, 1 out 92h, al in al, 92h .forever: cli hlt jmp .forever %ifdef DEBUG .s_szDbg: db 'Rebooting...', 0dh, 0ah, 0 %endif ENDPROC TestReboot_r86 ; ; Instantiate the template code. ; %include "bootsector2-template-footer.mac" ; reset the initial environemnt. ;%define TMPL_RM ;%include "bootsector2-test1-template.mac" ;%define TMPL_CMN_V86 ;%include "bootsector2-test1-template.mac" ;%define TMPL_PE16 ;%include "bootsector2-test1-template.mac" ;%define TMPL_PE32 ;%include "bootsector2-test1-template.mac" ;%define TMPL_PP16 ;%include "bootsector2-test1-template.mac" ;%define TMPL_PP32 ;%include "bootsector2-test1-template.mac" ;%define TMPL_PAE16 ;%include "bootsector2-test1-template.mac" ;%define TMPL_PAE32 ;%include "bootsector2-test1-template.mac" ;%define TMPL_LM16 ;%include "bootsector2-test1-template.mac" ;%define TMPL_LM32 ;%include "bootsector2-test1-template.mac" ;%define TMPL_LM64 ;%include "bootsector2-test1-template.mac" ; ; End sections and image. ; %include "bootsector2-common-end.mac"